8-Hour TWA Calculator (OSHA Time-Weighted Average & Mixture Formula)
The 8-hour time-weighted average exposure from up to four sampled periods, checked against a limit, plus the OSHA mixture formula for several substances at once.
Formula
E = (C1·T1 + C2·T2 + … + Cn·Tn) ÷ 8 (29 CFR 1910.1000(d)(1)). Mixture: Em = C1/L1 + C2/L2 + … + Cn/Ln, must not exceed 1 ((d)(2)).
Worked example
Inputs: Concentration, period 1 = 150 ppm or mg/m³; Hours, period 1 = 2 h; Concentration, period 2 = 75; Hours, period 2 = 2 h; Concentration, period 3 = 50; Hours, period 3 = 4 h; Concentration, period 4 (0 = none) = 0; Hours, period 4 = 0 h; 8-hour TWA limit (PEL) for comparison = 100 same units; Mixture: substance 1 TWA (optional) = 0; Mixture: substance 1 limit = 0; Mixture: substance 2 TWA = 0; Mixture: substance 2 limit = 0; Mixture: substance 3 TWA = 0; Mixture: substance 3 limit = 0.
| Eight hour twa | 81.25 |
|---|---|
| Hours entered | 8 |
| Pel check | At or below the 100 limit (81.3% of it) |
| Mixture equivalent exposure | — |
| Mixture check | No mixture entered |
OSHA 29 CFR 1910.1000(d)(1): E = (Ca·Ta + Cb·Tb + … + Cn·Tn) ÷ 8, with C in the limit's units (ppm or mg/m³) and T in hours; E must not exceed the substance's 8-hour TWA limit in Subpart Z. Hours you leave out count as zero exposure, so enter every period you sampled. (d)(2): for a mixture, Em = C1/L1 + C2/L2 + … must not exceed 1 (use each substance's 8-hour TWA as C). Ceiling and peak limits, and substance-specific standards (e.g. silica, lead), are checked separately.
FAQ
How do you calculate an 8-hour TWA?
Multiply each concentration by the hours at that level, add them up, and divide by 8. OSHA's example: (2 × 150 + 2 × 75 + 4 × 50) ÷ 8 = 81.25 ppm, under a 100 ppm limit.
What if I only sampled part of the shift?
The formula still divides by 8, so unsampled time counts as zero. Only do that if exposure was truly zero; otherwise sample the full shift or enter the unsampled period at a realistic level.
How does the mixture formula work?
Divide each substance's TWA by its own limit and add the ratios. OSHA's example: 500/1,000 + 45/200 + 40/200 = 0.925, which is under 1, so the combination is acceptable.
Is this the same as the noise TWA?
No. Noise uses a 5 dB exchange rate and a dose formula; use the noise exposure calculator.
Where do I find the limit?
OSHA Tables Z-1, Z-2 and Z-3 in 1910.1000 list 8-hour TWA PELs; some substances (silica, lead, benzene) have their own standards with lower limits and action levels.
Sources
Related
- Noise Exposure Calculator (OSHA Noise Dose % & 8-Hour TWA)
- Heat Index Calculator (NWS Formula, Danger Levels & OSHA Heat Notes)
- NIOSH Lifting Equation Calculator (RWL & Lifting Index)
More Safety calculators
- Wind Chill Calculator (NWS Formula, °F and °C)
- Sling Angle Calculator (Rigging Load Angle Factor & Tension per Leg)
- Porta Potty Calculator for Job Sites (OSHA Toilet Requirements per Worker)
Embed this calculator
Free to embed on your site; please keep the credit link.
Last reviewed 2026-11-20.